MR3420 Openwrt + MF823

-
 Kõigepealt tuleb installida vajalikud pakid:
opkg update
opkg install kmod-usb-net kmod-usb-net-rndis kmod-usb-net-cdc-ether usbutils udev usb-modeswitch

Seejärel seadistada pulga jaoks failid. Kasutasin rc.localis pulgalt korraks voolu tagant võtmise gpio-d, sest ilma ei hakanud tööle. Kindlasti on ka teisi võimalusi nt usb-modeswitch, aga nii toimis.

Faili sisu, et pulk tööle hakkaks
/etc/config/network:

    config 'interface' 'wan'
     option proto 'dhcp'
        option ifname usb0

/etc/rc.local sisu:
# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
sleep 5
echo 0 > /sys/devices/virtual/gpio/gpio6/value
sleep 2
echo 1 > /sys/devices/virtual/gpio/gpio6/value
exit 0

/etc/config/network:

config interface 'lan'
        option ifname 'eth0'
        option force_link '1'
        option type 'bridge'
        option proto 'static'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option ipaddr '192.168.100.1'
        option gateway '192.168.32.1'
        option dns '8.8.8.8'

Comments

Post a Comment

Popular posts from this blog

Making PCBs with 3D printer

-
Image
I always wanted to make PCBs at home. I have tried most of the processes from the internet to make PCB-s (by hand with marker, with printer and glossy paper, ....). Recently I got 3D printer and thought that the precision should be enough to make simple PCBs with it. So I searched from internet and found this page: http://www.lamja.com/?p=635 I had some old rod from an old printer from scrap. Next I designed a rod holder that would fit the printer. The printer is modified Ender 3 and has new cooling. So the rod holder had to be designed from scratch. I found some usable size spring that I made a bit bigger. I tried the process with marker and it worked but the result was not very good. So I had a idea to use nail polish and scrape that off with the rod. I used some random old nail polish. This resulted much better PCB board than the marker. Other parts of the process are the same as the link above. I had some trouble to get the *.svg file to FlatCam, because FlatCam...
Read more

ZTE MF29A router and Openwrt

-
Image
I got a MF29A router. I needed badly 3G router and with static ip leases, I was almost buying MR3420+3G stick. I cracked open the MF29A router, found some pins that were like serial port. Hooked up a serial port device and I was presented with bootlog. Stock firmware bootlog: U-Boot 1.1.3 (Feb 13 2012 - 16:50:17) Board: Ralink APSoC DRAM:  64 MB relocate_code Pointer at: 83fb0000 spi_wait_nsec: 1e spi device id: 1 2 16 4d 0 (2164d00) find flash: S25FL064P raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 3.5.0.0 -------------------------------------------- ASIC 3352_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: DDR2 DRAM_SIZE: 512 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 64 MBytes Flash component: SPI Flash FLASH_SIZE: 8 MB Date:Feb 13 2012  Time:16:50:17 ============================================ icache: s...
Read more

ESP8266 connection to MQTT server (Attempting MQTT connection...failed, rc=-2)

-
Recently I had a problem when trying to program NodeMCU with Arduino. I flashed arduino with basically default pubsubclient test program. After programming NodeMCU connected successfully to Wifi, then tried to connect MQTT server and failed: WiFi connected Attempting MQTT connection...connected ............Attempting MQTT connection...connected ............Attempting MQTT connection...failed, rc=-2 try again in 5 seconds I researched and tested many Arduino scripts. All failed with the same error -2. I logged into the MQTT server and watched logs. The NodeMCU didn't even connect to the MQTT server. I was clueless. Luckily I bought a few NodeMCUs from different sellers. Opened up another NodeMCU and hooked it up. Flashed the exact same code to it and it connected and worked like charm. Then I tried to flash the first problematic NodeMCU with Arduino and exactly the same error -2. I had also a ESP12E that had the -2 error before. Flashed it with the same code, still error -2. ...
Read more