Teamviewer 6 problem

-
The problem is that when connecting to Teamviewer 7 it says:

Your partner uses newer version of Teamviewer. Would you like to update Teamviewer now to establish connection?

Well for linux there isn't a newer version of teamviewer.
But, there is cure.
For me Teamviewer has installet itself in:
/usr/teamviewer/teamviewer/6/wine/drive_c/Program Files/Teamviewer/Version6/.......
Teamviewer uses wine to run the windows .exe file. So a nasty hack is to copy the windows installed version 7 files to linux and to same path.
I renamed in this path:
/usr/teamviewer/teamviewer/6/wine/drive_c/Program Files/Teamviewer/
Version6 folder to Version6_backup
Copied from windows install Version7 folder and renamed that to Version6.

Start teamviewer and enjoy.

Comments

  1. UnknownDecember 21, 2012 at 4:37 AM

    Try this http://www.ammyy.com/en/solutions.html

    Works well, doesn't require installation or specific config, works behind gateways NAT as well as within one LAN.

    ReplyDelete
  2. MarryJuly 18, 2016 at 7:30 AM

    Commodity trading form a unique quality category, which might be employed in combination with equity and debt assets to diversify one's portfolio, lower future risk and increase side potential. By the terribly nature of primary product, trade goods mercantilism generates many capitalist advantages that mercantilism in ancient assets cannot. https://www.behance.net/gallery/40527597/Ways-To-Set-Up-And-Crack-TeamViewer-11?

    ReplyDelete

Post a Comment

Popular posts from this blog

Making PCBs with 3D printer

-
Image
I always wanted to make PCBs at home. I have tried most of the processes from the internet to make PCB-s (by hand with marker, with printer and glossy paper, ....). Recently I got 3D printer and thought that the precision should be enough to make simple PCBs with it. So I searched from internet and found this page: http://www.lamja.com/?p=635 I had some old rod from an old printer from scrap. Next I designed a rod holder that would fit the printer. The printer is modified Ender 3 and has new cooling. So the rod holder had to be designed from scratch. I found some usable size spring that I made a bit bigger. I tried the process with marker and it worked but the result was not very good. So I had a idea to use nail polish and scrape that off with the rod. I used some random old nail polish. This resulted much better PCB board than the marker. Other parts of the process are the same as the link above. I had some trouble to get the *.svg file to FlatCam, because FlatCam...
Read more

ZTE MF29A router and Openwrt

-
Image
I got a MF29A router. I needed badly 3G router and with static ip leases, I was almost buying MR3420+3G stick. I cracked open the MF29A router, found some pins that were like serial port. Hooked up a serial port device and I was presented with bootlog. Stock firmware bootlog: U-Boot 1.1.3 (Feb 13 2012 - 16:50:17) Board: Ralink APSoC DRAM:  64 MB relocate_code Pointer at: 83fb0000 spi_wait_nsec: 1e spi device id: 1 2 16 4d 0 (2164d00) find flash: S25FL064P raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 3.5.0.0 -------------------------------------------- ASIC 3352_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: DDR2 DRAM_SIZE: 512 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 64 MBytes Flash component: SPI Flash FLASH_SIZE: 8 MB Date:Feb 13 2012  Time:16:50:17 ============================================ icache: s...
Read more

ESP8266 connection to MQTT server (Attempting MQTT connection...failed, rc=-2)

-
Recently I had a problem when trying to program NodeMCU with Arduino. I flashed arduino with basically default pubsubclient test program. After programming NodeMCU connected successfully to Wifi, then tried to connect MQTT server and failed: WiFi connected Attempting MQTT connection...connected ............Attempting MQTT connection...connected ............Attempting MQTT connection...failed, rc=-2 try again in 5 seconds I researched and tested many Arduino scripts. All failed with the same error -2. I logged into the MQTT server and watched logs. The NodeMCU didn't even connect to the MQTT server. I was clueless. Luckily I bought a few NodeMCUs from different sellers. Opened up another NodeMCU and hooked it up. Flashed the exact same code to it and it connected and worked like charm. Then I tried to flash the first problematic NodeMCU with Arduino and exactly the same error -2. I had also a ESP12E that had the -2 error before. Flashed it with the same code, still error -2. ...
Read more